My Igniter Is Not Working How Do I Fix It
If the igniter for your grill stops working it can be helpful to try a few things before replacing the ignition system with a replacement igniter kit.
To help determine the cause of the problem as quickly as possible, please consider the following.
Grill Wont Maintain Stable Temps In Cold Weather
When the temperature outside dips below 50 degrees, the propane may be taking too long to transform into vapor. This can restrict the gas flow, which means that the grill wont be able to hold its heat long enough to cook your ingredients.
Check the outside of the LP tank. Is it coated in frost or ice? If so, it will need to be disconnected and replaced with a new one.
The Battery Is Dead Or Corroded
Dead batteries are one of the most common causes of igniter issues. If you have a battery-powered spark generator, the first thing to try is replacing the battery. Concerns about battery life are not applicable to piezo igniters.
Replace the battery by turning the igniter button cover counterclockwise to remove it. Take out the old battery, insert a fresh one, and try lighting your grill. If the battery is corroded or the igniter still wont spark after you replace it, the igniter may simply be dirty or need reconnecting.
GRILL SPOT TIP:
Also Check: Oceans One Bar And Grill
How Do I Light My Weber Grill If Ignitor Is Broken
Placing the match in the match stick holder and striking the match to light it are two ways to go. Then put the match holder with the lit match down through the cooking grates, past the flavorizer bars, and into the area adjacent to the left burner on the stovetop burner. Ignite the burners one at a time, working your way from left to right.
Why Isnt My Grill Getting Gas
Gas grill: the burners do not receive gas. First, check tank propane level to make sure tank has gas. Then, reset the pressure regulator to restore gas flow through the regulator if the regulators flow limiting device has tripped. Obstructions in the burner tubes can also prevent gas flow through the tubes.
Don’t Miss: City Grill And Wings Harrisburg
How Do You Check Pulse Igniter
If the pulse igniter clicks but the flame does not ignite, check the following: Make sure the gas line is connected correctly. Check the pilot light. Is the pilot light lit? If the pilot light is not lit, remove the cap from the top of the stove. Turn the knob to the off position. Remove the burner plate. Using a long match, light the pilot light. Replace the burner plate. Turn the knob to on position. Reattach the burner plate. Light the burner. If the burner still does not light, replace the burner plate.
The Electrodes Are Dirty Or Corroded
Igniters are frequently subjected to dirt and debris from cooking fumes, grease, and food particles. If the electrodes are covered in gunk from months of grilling, your igniter wont be able to spark.
Dirty electrodes are easy to fixall you need to do is clean them using a cotton swab and a bit of rubbing alcohol. Gently rub the swab over the metal tip of the electrode, let it dry, and attempt to start the grill. It may take a few tries to get the electrode totally clean.
Electrodes can also become corroded from exposure to moisture, which can prevent a spark from generating. If your electrodes are corroded, you can lightly sand off the corrosion.
Recommended Reading: Recipe For Grilled Rack Of Lamb
Why Is My Stove Igniter Keeps Clicking
Food debris can accumulate in the igniter, which is the reason for it to keep clicking when it is turned off. The food stuck in the igniter can result in the system to turn off. Dislodging the food debris should stop the stove from clicking when turned off.
How do I stop my gas igniter from clicking?
Food Debris Causing Igniters to Click When Off
What Kind Of Ignition System Does Weber Use
Each time you depress the button, a spark is generated. Since the mid-2000s, Weber has used a combination of mechanical piezo ignition systems and battery-powered electronic ignition systems in gas grills. The mechanical ignition system is known as Snap-Jet and is integrated into each gas burner control knob.
What should I do if my Weber spark plug fails?
We recommend disconnecting and reconnecting all igniter wires to ensure no loose connections. Do you hear any clicking when you press the igniter button? If not and youve replaced the battery, the module may have failed. For help with a replacement module please email us at or give us a call at 800-446-1071.
Breakdown Of The Grill Ignition System
The main parts of a grill ignition will consist of a spark generator , electrodes, collector boxes and wires. The spark generator comes in either a battery form or piezo. The battery spark generator may contain switch or it will have a plug that for a trigger switch. If you hear a constant clicking noise, your spark module is still working. The piezo creates a hard snap. This type of ignition was used on older Weber, DCS and Viking grills.
Unscrew the cap on the battery spark generator and check the battery. The environmental elements can corrode the battery inside and damage the internal working of the spark igniter causing it to stop working. If you do not hear the continual clicking from the spark module be sure to put in a new battery. Many grills today use a battery ignition system like Charbroil, TEC, Delta Heat, Weber, Nexgrill and more. If you hear the continual clicking … it works. If you do not … it’s broken and needs replacing.
The spark generator will have one to eight outlets to plug in the electrode wires. Some grills will use one electrode to spark one burner and have carry over tubes to light the additional burners. While others have an electrode for each individual burner.
Here you can identify the various spark generators that have been used in grills of yesterday and today….
This a rotary piezo igniter that creates a hard snap which the knob is turned.
This is a “AA” Spark Generator that has a push button to ignite the grill.
Types Of Ignition Systems
Prior to the mid-2000s, Weber used a mechanical piezo ignition system in gas grills. When you depress the ignition button, a spring-loaded hammer hits a crystal, generating a high voltage discharge that travels through wires to a ceramic igniter in the firebox, creating a spark next to the burner tube and lighting the gas. These older systems make a loud metallic bang noise when you depress the rectangular ignition button. Each time you depress the button, a spark is generated.
Since the mid-2000s, Weber has used a combination of mechanical piezo ignition systems and battery-powered electronic ignition systems in gas grills. The mechanical ignition system is known as Snap-Jet and is integrated into each gas burner control knob. When the knob is turned to the START/HI position, the mechanical igniter generates a spark that lights the gas. The name Snap-Jet is derived from the loud snap noise that occurs when the knob is turned.
Youll find Snap-Jet igniters on Summit gas grills manufactured from 2003 until time of this writing. On these grills, the igniters are integrated into the gas manifold. If you have a bad igniter, you have to replace the entire gas manifold assembly, a part that costs around $100 at the time of this writing. Not such a great design from a maintenance perspective!
The Go-Anywhere gas grill uses a mechanical igniter.
There are a bunch of different versions of these electronic systems, so making sure you buy the right replacement is critical.
A Wire Is Loose In The Grill
Finally, there could also be a problem with one of the wires in the grill.There are a lot of electrical components in your grill even if it uses gas. Therefore, there are a lot of wires that connect these components as well. If there is a wire that is loose, your grill is not going to be able to light properly.
It can be difficult to take a look at the individual wires of your grill. That is why you should reach out to a professional who can do this for you. A professional will be able to let you know if there is something wrong with one of the wires. Then, you can replace them if that is required.
Why Does My Weber Grill Smell Like Gas
Sometimes most awkward things happen in grill that there is gas smell on grill. Though it is very rears to the Weber grills, if you found that problem you should find the issue. Probably it happen if there is any leakage on gas, spray soapy water throughout the regulator and search for any bubbles.
Make sure that the igniter is making a clicking noise when you press the igniter button. If it doesnt click, then the wires may not be connected properly, the battery may be dead or installed incorrectly, or the igniter module may have failed.
Cleaning & Aligning Weber Bbq Grill
Debris, burnt grease, or carbon buildup on your burner can block the ports which the flame comes through. This can lead to yellow flame. Follow the instructions in your owner’s manual on how to safely clean your Weber BBQ Grill.
Yellow flames persisting? You could have an alignment problem. Your manifold, control valve, and burners might not be aligned in the best possible way. Your gas needs to flow as straight as possible through all the parts of your Weber BBQ Grill. Inspect the entire flow and be sure all parts are properly aligned and undamaged.
If you find that you still have the yellow flame on all the burners, then you need to replace your regulator. If the problem is with only one burner, then you most likely still have a clog or that part may be faulty.
Popular Mechanical Igniter Replacement Kits
The two most popular mechanical igniter replacement kits are:
- Weber 7509 Igniter Kit: For Spirit and Genesis , Platinum I and II, Genesis 1000 to 5500, Genesis Silver and Gold , and Genesis Platinum. Does not fit Spirit front-mounted control panel models.
- Weber 7510 Igniter Kit: For Genesis Silver/Gold/Platinum gas grills and Spirit 200/300 gas grills . Does not fit Genesis Silver/Gold C models after 2003.
These kits come with an igniter button that generates the high voltage discharge, a ceramic igniter that makes the spark, a black wire and a white wire, a sheet metal gas catcher that collects gas , and installation instructions. The black wire is connected at one end to the ceramic igniter at the factory.
If you have a grill with a mechanical igniter thats not listed above, call Weber Customer Support at 800-446-1071 to determine the correct igniter for your grill. For example, Ive got a 2002 Weber Summit 450 grill with two mechanical igniters and the replacement part is Weber 901a part that looks identical to the Weber 7509 shown above, but theres some difference between the twoperhaps the wires are a different length.
How Do You Light A Gas Grill When The Igniter Doesnt Work
If you notice that your gas grill igniter isnt lighting up, youll want to turn off the gas supply to the burner. Then, open the hood of the grill and remove the igniter assembly. Check to make sure that the igniter is plugged into the correct socket. If its not, replace it. If the igniter is plugged in correctly, check the wiring connection between the igniter and the gas line. Make sure that the wires arent frayed or damaged. Also, make sure that the ignitor circuit breaker is turned off. If the ignitor circuit breaker isnt turned off, flip it back on. After doing these steps, reattach the igniter assembly to the grill and test it again. If it still doesnt light up, call a professional repair service.
How do I clean my electric oven?
Grill Light Wont Turn On
If the lid of your Weber grill is equipped with lights for evening cookouts, it will only activate when the lid is open. Try pressing the AWAKE button once youve lifted the lid. Battery replacement might also be in order.
Remember that the light will automatically shut off after 30 minutes if theres been no grill activity during that time. You can relight it by pressing the AWAKE button.
When the light wont shut off, its probably because the lid of the grill is ajar. Make sure to close it completely when youve finished grilling.
Gas Grill Igniter Stopped Working
Here at The BBQ Depot, we have repaired thousands of gas grills. Generally, the one of the first parts on a bbq to fail is the burner and not the ignition. Barbecue igniters will work for years.
We get many calls from customers saying, “My grill will not light” or “My igniter is broken.”
Just because the igniter is not working does not mean that it is actually broken. We will need to troubleshoot.
Can I Light My Grill Manually
In the event your ignition stops working, you can manually light your grill and save your barbecue! It can be a bit intimidating if you have never manually lit a grill before, but rest assured that as long as you follow the simple instructions below it can be done easily and safely.
Please note that these instructions only apply to current models. For older models, please reference the instructions in your owners manual. Click here to find out how to locate your owners manual online.
Liquid Propane Grills
Natural Gas Grills
WARNING: Do not lean over the open barbecue when lighting your grill.
St John Restaurants Ocean Grill At Cruz Bay St John Usvi
In order to ensure that when you touch the igniter button, an audible click may be heard from the igniter. If the button does not click, it is possible that the wires are not properly connected, that the battery is dead or that the battery has been installed incorrectly, or that the igniter module has failed.
Why Is My Grill Clicking
The battery spark generator may contain switch or it will have a plug that for a trigger switch. If you hear a constant clicking noise, your spark module is still working. The environmental elements can corrode the battery inside and damage the internal working of the spark igniter causing it to stop working.
All You Need To Know About Buying Grill Igniters For Weber
How do I know which Weber grill I have?
- Located on the inside of the tank panel, below the cookbox. OR.
- Located underneath the control panel.
Besides, why is my igniter not clicking?
DOES THE IGNITER MAKE A CLICKING NOISE? Make sure that the igniter is making a clicking noise when you press the igniter button. If it doesn’t click, then the wires may not be connected properly, the battery may be dead or installed incorrectly, or the igniter module may have failed.
Accordingly, how long do Weber igniters last?
Completely redesigned and backed by an industry leading warranty, these igniters are built to last. We increased the warranty from 2 to 10 years! No that’s not a typo, these igniters are guaranteed for a decade!
Inside Of Lid Is Peeling
If the inside of your grill lid looks like its peeling, the issue is caused by grease buildup. The burned-on grease has turned to carbon, which is now beginning to flake off. Because the cookbox is made of cast aluminum and is not painted, it wont actually peel on its own. Cleaning the lid will resolve the issue.
How Do You Know If An Igniter Grill Is Bad
Manually ignite the grill using a match or lighter fluid. If it does not light, the fault is most likely with the igniter. If the burner does not ignite, it is possible that the problem is due to a blocked or filthy burner. Clean the burner and re-test the igniter to ensure it is working properly.
How Do You Manually Light A Weber Spirit
If you have a Spirit or Spirit II model, you can follow the steps below or consult your owners handbook for assistance.